Engine
Showing 4321–4360 of 9204 results
-
Rubber BearingJohnson 1”x 1-1/4”x 4″ Cutless Naval Brass Sleeve Bearings
Johnson 1”x 1-1/4”x 4″ Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Apex Cutlass Bearing
A:Shaft Diameter (inches): 1
B:Outside Diameter (inches): 1 and 1/4
C:Length (inches): 4
G:Metal Thickness (inches): 3/64• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$76.35 Add to cart -
Marine Safety EquipmentOrion Alerter Basic (4) 12-Gauge Launcher and Aerial Signal Pack 584
Orion Alerter Basic – (4) 12-Gauge Launcher and Aerial Signal Pack 584
• Includes: 12-Gauge Safety
Launcher with bandolier that
can hold up to 6 High Performance Lighting
Signals and (4) 12-Gauge High
Performance Red Aerial Signals. Anchor
& Dock • USCG Approved for day and nighttime signa• Brand :ORION SAFETY PRODUCTS
(0 reviews)$89.99 Add to cart -
Rubber Bearing
Johnson 1”x 1-1/2”x 4” Cutless Naval Brass Sleeve Bearings
Johnson 1”x 1-1/2”x 4” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Apex Cutlass Bearing
A:Shaft Diameter (inches): 1
B:Outside Diameter (inches): 1 and 1/2
C:Length (inches): 4
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$79.02 Add to cart -
Rubber Bearing
Johnson 1”x 1-5/8”x4” Cutless Naval Brass Sleeve Bearings
Johnson 1”x 1-5/8”x4” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Apex Cutlass Bearing
A:Shaft Diameter (inches): 1
B:Outside Diameter (inches): 1 and 5/8
C:Length (inches): 4
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$80.41 Add to cart -
Rubber Bearing
Johnson 1”x 1-3/8”x 4” Cutless Naval Brass Sleeve Bearings
Johnson 1”x 1-3/8”x 4” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Apex Cutlass Bearing
A:Shaft Diameter (inches): 1
B:Outside Diameter (inches): 1 and 3/8
C:Length (inches): 4
G:Metal Thickness (inches): 1/16• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$80.64 Add to cart -
Rubber Bearing
Johnson 1-1/4”x 1-1/2”x 5” Cutless Naval Brass Sleeve Bearings
Johnson 1-1/4”x 1-1/2”x 5” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 1/4
B:Outside Diameter (inches): 1 and 1/2
C:Length (inches): 5
G:Metal Thickness (inches): 1/16• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$102.03 Add to cart -
Rubber Bearing
Johnson 1-1/4”x 1-3/4”x 5 Cutless Naval Brass Sleeve Bearings
Johnson 1-1/4”x 1-3/4”x 5 Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 1/4
B:Outside Diameter (inches): 1 and 3/4
C:Length (inches): 5
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$115.86 Add to cart -
Rubber Bearing
Johnson 1-1/4”x 2”x 5” Cutless Naval Brass Sleeve Bearings
Johnson 1-1/4”x 2”x 5” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 1/4
B:Outside Diameter (inches): 2
C:Length (inches): 5
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$108.10 Add to cart -
Rubber Bearing
Johnson 1”x 2”x 4 Cutless Naval Brass Sleeve Bearings
Johnson 1”x 2”x 4 Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1
B:Outside Diameter (inches): 2
C:Length (inches): 4
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$103.89 Add to cart -
Rubber Bearing
Johnson 1-1/4”x 2-1/8”x 5” Cutless Naval Brass Sleeve Bearings
Johnson 1-1/4”x 2-1/8”x 5” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 1/4
B:Outside Diameter (inches): 2 and 1/8
C:Length (inches): 5
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$120.87 Add to cart -
Rubber Bearing
Johnson 1-1/8”X 1-1/2”X 4-1/2” Cutless Naval Brass Sleeve Bearings
Johnson 1-1/8”X 1-1/2”X 4-1/2” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 1/8
B:Outside Diameter (inches): 1 and 1/2
C:Length (inches): 4 and 1/2
G:Metal Thickness (inches): 1/16• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$100.71 Add to cart -
Rubber Bearing
Johnson 1-1/8”X 1-3/4”X 4-1/2” Cutless Naval Brass Sleeve Bearings
Johnson 1-1/8”X 1-3/4”X 4-1/2” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 1/8
B:Outside Diameter (inches): 1 and 3/4
C:Length (inches): 4 and 1/2
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$115.32 Add to cart -
Rubber Bearing
Johnson 1-1/8”x 2” x 4-1/2” Cutless Naval Brass Sleeve Bearings
Johnson 1-1/8”x 2” x 4-1/2” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 1/8
B:Outside Diameter (inches): 2
C:Length (inches): 4 and 1/2
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$154.61 Add to cart -
Rubber Bearing
Johnson 1-3/8”x 2”x 5-1/2” Cutless Naval Brass Sleeve Bearings
Johnson 1-3/8”x 2”x 5-1/2” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 3/8
B:Outside Diameter (inches): 2
C:Length (inches): 5 and 1/2
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$124.42 Add to cart -
Rubber Bearing
Johnson 1-3/8”x 2-3/8”x 5-1/2 Cutless Naval Brass Sleeve Bearings
Johnson 1-3/8”x 2-3/8”x 5-1/2 Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 3/8
B:Outside Diameter (inches): 2 and 3/8
C:Length (inches): 5 and 1/2
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$136.88 Add to cart -
Rubber Bearing
Johnson 1-1/2”x 2” x 6” Cutless Naval Brass Sleeve Bearings
Johnson 1-1/2”x 2” x 6” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 1/2
B:Outside Diameter (inches): 2
C:Length (inches): 6
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$141.84 Add to cart -
Rubber Bearing
Johnson 1-1/2”x 2-3/8” x 6” Cutless Naval Brass Sleeve Bearings
Johnson 1-1/2”x 2-3/8” x 6” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 1/2
B:Outside Diameter (inches): 2 and 3/8
C:Length (inches): 6
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$150.07 Add to cart -
Rubber Bearing
Johnson) 1-3/4”x 2-3/8 ”x 7” Cutless Naval Brass Sleeve Bearings
Johnson 1-3/4”x 2-3/8 ”x 7” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 3/4
B:Outside Diameter (inches): 2 and 3/8
C:Length (inches): 7
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$174.46 Add to cart -
Rubber Bearing
Johnson 1-3/4”x 2-5/8”x 7” Cutless Naval Brass Sleeve Bearings
Johnson 1-3/4”x 2-5/8”x 7” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 3/4
B:Outside Diameter (inches): 2 and 5/8
C:Length (inches): 7
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$178.70 Add to cart -
Rubber Bearing
Johnson 2”x 2-5/8”x 8 Cutless Naval Brass Sleeve Bearings
Johnson 2”x 2-5/8”x 8 Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 2
B:Outside Diameter (inches): 2 and 5/8
C:Length (inches): 8
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$199.90 Add to cart -
Rubber Bearing
Johnson 2”x 3”x 8 Cutless Naval Brass Sleeve Bearings
Johnson 2”x 3”x 8 Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 2
B:Outside Diameter (inches): 3
C:Length (inches): 8
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$204.02 Add to cart -
Rubber Bearing
Johnson 2-1/4”x 3-1/8” x 9″ Cutless Naval Brass Sleeve Bearings
Johnson 2-1/4”x 3-1/8” x 9″ Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 2 and 1/4
B:Outside Diameter (inches): 3 and 1/8
C:Length (inches): 9
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$258.53 Add to cart -
Rubber Bearing
Johnson 2-1/4” x 2-15/16” x 9″ Cutless Naval Brass Sleeve Bearings
Johnson 2-1/4” x 2-15/16” x 9″ Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 2 and 1/4
B:Outside Diameter (inches): 2 and 15/16
C:Length (inches): 9
G:Metal Thickness (inches): 3/32• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$596.39 Add to cart -
Rubber Bearing
Johnson 2-1/2 x 3-1/8” x 10” Cutless Naval Brass Sleeve Bearings
Johnson 2-1/2 x 3-1/8” x 10” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 2 and 1/2
B:Outside Diameter (inches): 3 and 1/8
C:Length (inches): 10
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$303.25 Add to cart -
Rubber Bearing
Johnson 2-1/2” x 3-3/8” x 10” Cutless Naval Brass Sleeve Bearings
Johnson 2-1/2” x 3-3/8” x 10” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 2 and 1/2
B:Outside Diameter (inches): 3 and 3/8
C:Length (inches): 10
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$304.90 Add to cart -
Rubber Bearing
Johnson 2-3/4” x 3-3/8” x 11” Cutless Naval Brass Sleeve Bearings
Johnson 2-3/4” x 3-3/8” x 11” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 2 and 1/4
B:Outside Diameter (inches): 3 and 1/8
C:Length (inches): 9
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$352.99 Add to cart -
Rubber Bearing
Johnson 2-3/4” x 3-3/4” x 11” Cutless Naval Brass Sleeve Bearings
Johnson 2-3/4” x 3-3/4” x 11” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 2 and 3/4
B:Outside Diameter (inches): 3 and 3/4
C:Length (inches): 11
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$371.90 Add to cart -
Rubber Bearing
Johnson 3”x 4”x 12″ Cutless Naval Brass Sleeve Bearings
Johnson 3”x 4”x 12″ Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 3
B:Outside Diameter (inches): 3 and 3/4
C:Length (inches): 12
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$375.92 Add to cart -
Rubber Bearing
Johnson 3-1/2”x 4-1/2” x 14”Cutless Naval Brass Sleeve Bearings
Johnson 3-1/2”x 4-1/2” x 14” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 3 and 1/2
B:Outside Diameter (inches): 4 and 1/2
C:Length (inches): 14
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$506.34 Add to cart -
Rubber Bearing
Johnson 3-1/2”x 4-1/4” x 14 Cutless Naval Brass Sleeve Bearings
Johnson 3-1/2”x 4-1/4” x 14 Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 3 and 1/2
B:Outside Diameter (inches): 4 and 1/4
C:Length (inches): 14
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$505.05 Add to cart -
Rubber Bearing
Johnson 3-5/8” x 4-1/2” x14-1/2” Cutless Naval Brass Sleeve Bearings
Johnson 3-5/8” x 4-1/2” x14-1/2” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 3 and 5/8
B:Outside Diameter (inches): 4 and 1/2
C:Length (inches): 14 and 1/2
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$720.32 Add to cart -
Rubber Bearing
Johnson 4” x 5” x 16”Cutless Naval Brass Sleeve Bearings
Johnson 4” x 5” x 16” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 4
B:Outside Diameter (inches): 5
C:Length (inches): 16
G:Metal Thickness (inches): 3 and 1/6• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$775.20 Add to cart -
Rubber Bearing
Johnson 4-1/2” x 5-1/2” x 18” Cutless Naval Brass Sleeve Bearings
Johnson 4-1/2” x 5-1/2” x 18” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 4 and 1/2
B:Outside Diameter (inches): 5 and 1/2
C:Length (inches): 18
G:Metal Thickness (inches): 3 1/6• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$998.75 Add to cart -
Rubber Bearing
Johnson 4”x 5-1/4” x 16 Cutless Naval Brass Sleeve Bearings
Johnson 4”x 5-1/4” x 16 Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 4
B:Outside Diameter (inches): 5 and 1/4
C:Length (inches): 16
G:Metal Thickness (inches): 3 and 1/6• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$855.42 Add to cart -
Rubber Bearing
Johnson 4-1/2”x 5-3/4” x 18” Cutless Naval Brass Sleeve Bearings
Johnson 4-1/2”x 5-3/4” x 18” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 4 and 1/2
B:Outside Diameter (inches): 5 and 3/4
C;Length (inches): 18
G:Metal Thickness (inches): 3/16• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$1,424.98 Add to cart -
Rubber Bearing
Johnson 5” x 6-1/8”x 20”Cutless Naval Brass Sleeve Bearings
Johnson 5” x 6-1/8”x 20” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 5
B:Outside Diameter (inches): 6 and 1/8
C:Length (inches): 20
G:Metal Thickness (inches): 1/4• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$1,806.60 Add to cart -
Rubber Bearing
Johnson 5” x 6-1/2” x 20”Cutless Naval Brass Sleeve Bearings
Johnson 5” x 6-1/2” x 20” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 5
B:Outside Diameter (inches): 6 and 1/2
C:Length (inches): 20
G:Metal Thickness (inches): 1/4• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$1,537.08 Add to cart -
Rubber Bearing
Johnson 5-1/2” x 7” x 22” Cutless Naval Brass Sleeve Bearings
Johnson 5-1/2” x 7” x 22” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 5 and 1/2
B:Outside Diameter (inches): 7
C:Length (inches): 22
G:Metal Thickness (inches): 1/4• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$2,005.10 Add to cart -
Rubber Bearing
Johnson 5-3/4” x 7” x 23 Cutless Naval Brass Sleeve Bearings
Johnson 5-3/4” x 7” x 23 Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 5 and 3/4
B:Outside Diameter (inches): 7
C:Length (inches): 23
G:Metal Thickness (inches): 1/4• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews) -
Rubber Bearing
Johnson 6”x 7-1/2” x 24” Cutless Naval Brass Sleeve Bearings
Johnson 6”x 7-1/2” x 24” Cutless Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 6
B:Outside Diameter (inches): 7 and 1/2
C:Length (inches): 24
G:Metal Thickness (inches): 1/4• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$2,240.24 Add to cart
