Showing 6201–6240 of 13001 results
-
Marine Safety EquipmentJim-Buoy Life Floats 10 Man Life Float with Tape
Jim-Buoy Life Floats 10 Man Life Float with Tape
• Person Capacity :10
• Length : 63”
• Width : 37″
• Diameter :9”
• Weight : 25 lbs.
• International Orange.
• Tough resilient vinyl surface.
• Lightweight yet easily exceeds the most severe USCG test.
• No exposed metal hardware – all double webbing beckets secured inside
the float body.
• Solid closed-cell plastic throughout.
• Double webbing, sunlight or weather never reaches the supporting
beckets.
• USCG Approved.
• Shipped by motor freight only• Brand :CAL-JUNE INC.
(0 reviews)$4,276.80 Add to cart -
Marine Safety Equipment
Jim-Buoy Life Floats 12 Man Life Float with Tape
Jim-Buoy Life Floats 12 Man Life Float with Tape
• Person Capacity :12
• Length : 78”
• Width : 37″
• Diameter :9”
• Weight : 25 lbs.
• International Orange.
• Tough resilient vinyl surface.
• Lightweight yet easily exceeds the most severe USCG test.
• No exposed metal hardware – all double webbing beckets secured inside
the float body.
• Solid closed-cell plastic throughout.
• Double webbing, sunlight or weather never reaches the supporting
beckets.
• USCG Approved.
• Shipped by motor freight only• Brand :CAL-JUNE INC.
(0 reviews)$4,716.80 Add to cart -
Marine Safety Equipment
Jim-Buoy Life Floats 15 Man Life Float with Tape
Jim-Buoy Life Floats 15 Man Life Float with Tape
• Person Capacity :15
• Length : 64”
• Width : 48″
• Diameter :12.5”
• Weight : 50 lbs.
• International Orange.
• Tough resilient vinyl surface.
• Lightweight yet easily exceeds the most severe USCG test.
• No exposed metal hardware – all double webbing beckets secured inside
the float body.
• Solid closed-cell plastic throughout.
• Double webbing, sunlight or weather never reaches the supporting
beckets.
• USCG Approved.
• Shipped by motor freight only• Brand :CAL-JUNE INC.
(0 reviews)$5,638.80 Add to cart -
Marine Safety Equipment
Jim-Buoy Life Floats 22 Man Life Float with Tape
Jim-Buoy Life Floats 22 Man Life Float with Tape
• Person Capacity :22
• Length : 100”
• Width : 48″
• Diameter :12.5”
• Weight : 70 lbs.
• International Orange.
• Tough resilient vinyl surface.
• Lightweight yet easily exceeds the most severe USCG test.
• No exposed metal hardware – all double webbing beckets secured inside
the float body.
• Solid closed-cell plastic throughout.
• Double webbing, sunlight or weather never reaches the supporting
beckets.
• USCG Approved.
• Shipped by motor freight only• Brand :CAL-JUNE INC.
(0 reviews)$6,867.64 Add to cart -
UncategorizedJohn Deere Engine Parts
Item # Qty Description RE520953 1 Engine Controller RE516335 1 Pressure relief Valve AT329939 1 Compensator (0 reviews)$4,269.11 Add to cart -
Marine Safety EquipmentTaylortec Vinyl Dip ,3x Coated Work Vests (WV-10RTXXXL)
Taylortec Vinyl Dip ,3x Coated Work Vests (WV-10RTXXXL)
• Size : XLG
• Shoulder :15
• Chest :66
• Waist: 62
• Inherently buoyant, 3 piece vinyl
coated foam work vest.
• USCG Approval 160.053/70/0.
• Minimum Buoyancy as required by U.S.C.G. is 17-1/2 lbs, Taylortec’s
Design Buoyancy = 18-3/4 ± 1/2 lbs.
• PVC based closed cell foam, liquid vinyl, 1” black polypropylene webbing,
aluminum slides, plastic or stainless steel buckle, reflective tape is
optional.
• All materials are U.S.C.G. and U.L. approved.• Brand :TAYLORTEC, INC.
(0 reviews)$78.43 Add to cart -
Marine Safety Equipment
Taylortec Vinyl Coated Work Vests PVC,USCGV WV-10RT
Taylortec Vinyl Coated Work Vests PVC,USCGV WV-10RT (Adult)
• Size : Regular
• Shoulder :12
• Chest :34″
• Waist: 52″
• Inherently buoyant, 3 piece vinyl
coated foam work vest.
• USCG Approval 160.053/70/0.
• Minimum Buoyancy as required by U.S.C.G. is 17-1/2 lbs, Taylortec’s
Design Buoyancy = 18-3/4 ± 1/2 lbs.
• PVC based closed cell foam, liquid vinyl, 1” black polypropylene webbing,
aluminum slides, plastic or stainless steel buckle, reflective tape is
optional.
• All materials are U.S.C.G. and U.L. approved.• Brand :TAYLORTEC, INC
(0 reviews)$81.04 Add to cart -
Rubber BearingJohnson 3/4″ x 1 1/4″ x 3″ Cutless Naval Brass Sleeve Bearings
Johnson 3/4″ x 1 1/4″ x 3″ Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A :Shaft Diameter (inches): 3/4
B:Outside Diameter (inches): 1 and 1/4
C:Length (inches): 3
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$73.80 Add to cart -
Marine Safety EquipmentStearns Force™ II Work Vests PVC USCG V Chest Size 34” – 52”
Stearns Force™ II Work Vests PVC USCG V Chest Size 34” – 52”(Adult)
• Aquafoam flotation foam retains
buoyancy, even when punctured.
• 3M Scotchlite SOLAS – grade reflective
strips on the front and back improve visibility.
• Compatible with most types of fall protection harnesses for added safety.
• Dual encircling belts with snag-resistant buckles securely adhere to the
body.
• Self-extinguishing construction reduces fire danger risks.
• Delrin snap hooks and D-ring for added convenience.
• 17.5 lbs. of buoyancy.
• USCG Approved Type V• Brand :STEARNS MFG. CO
(0 reviews)$64.12 Add to cart -
Marine Safety Equipment
Stearns Force™ II Work Vests PVC USCG V Chest Size 52” – 62”
Stearns Force™ II Work Vests PVC USCG V Chest Size 52” – 62” (Oversize)
• Aquafoam flotation foam retains
buoyancy, even when punctured.
• 3M Scotchlite SOLAS – grade reflective
strips on the front and back improve visibility.
• Compatible with most types of fall protection harnesses for added safety.
• Dual encircling belts with snag-resistant buckles securely adhere to the
body.
• Self-extinguishing construction reduces fire danger risks.
• Delrin snap hooks and D-ring for added convenience.
• 17.5 lbs. of buoyancy.
• USCG Approved Type V• Brand :STEARNS MFG. CO
(0 reviews)$81.05 Add to cart -
Marine Safety EquipmentImperial Work Vest Vinyl-Dipped 280RT
Imperial Work Vest Vinyl-Dipped (280RT) Adult
• Lenght 3.5
• Width 11.5
•Height : 23″
• A smooth, durable vinyl coating over
self- extinguishing contoured flotation
foam panels which are resistant to
deterioration.
• Foam retains buoyancy even when
punctured.
• Opening on back panel accommodates
most harnesses.
• Adjustable chest and shoulder straps.
• Minimum 15.5 lbs. of buoyancy.
• 17.5 square inches of SOLAS-grade reflective tape.
• Adult universal size: For adults over 90 lbs., chest size of 32” – 54”.
• USCG Approved Type V, CFR 160.053 compliant and CFR 1926.106 (OSHA)
compliant• Brand :SURVITEC GROUP
(0 reviews)$80.37 Add to cart -
Rubber Bearing
Johnson 7/8”x1-3/8”x 3-1/2” Cutless Naval Brass Sleeve Bearings
Johnson 7/8”x 1-3/8”x 3-1/2” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Apex Cutlass Bearing
A:Shaft Diameter (inches): 7/8
B :Outside Diameter (inches): 1 and 3/8
C :Length (inches): 3 and 1/2
G :Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$78.06 Add to cart -
Rubber Bearing
Johnson 1”x 1-1/4”x 4″ Cutless Naval Brass Sleeve Bearings
Johnson 1”x 1-1/4”x 4″ Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Apex Cutlass Bearing
A:Shaft Diameter (inches): 1
B:Outside Diameter (inches): 1 and 1/4
C:Length (inches): 4
G:Metal Thickness (inches): 3/64• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$76.35 Add to cart -
Marine Safety EquipmentOrion Alerter Basic (4) 12-Gauge Launcher and Aerial Signal Pack 584
Orion Alerter Basic – (4) 12-Gauge Launcher and Aerial Signal Pack 584
• Includes: 12-Gauge Safety
Launcher with bandolier that
can hold up to 6 High Performance Lighting
Signals and (4) 12-Gauge High
Performance Red Aerial Signals. Anchor
& Dock • USCG Approved for day and nighttime signa• Brand :ORION SAFETY PRODUCTS
(0 reviews)$89.99 Add to cart -
Rubber Bearing
Johnson 1”x 1-1/2”x 4” Cutless Naval Brass Sleeve Bearings
Johnson 1”x 1-1/2”x 4” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Apex Cutlass Bearing
A:Shaft Diameter (inches): 1
B:Outside Diameter (inches): 1 and 1/2
C:Length (inches): 4
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$79.02 Add to cart -
Rubber Bearing
Johnson 1”x 1-5/8”x4” Cutless Naval Brass Sleeve Bearings
Johnson 1”x 1-5/8”x4” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Apex Cutlass Bearing
A:Shaft Diameter (inches): 1
B:Outside Diameter (inches): 1 and 5/8
C:Length (inches): 4
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$80.41 Add to cart -
Rubber Bearing
Johnson 1”x 1-3/8”x 4” Cutless Naval Brass Sleeve Bearings
Johnson 1”x 1-3/8”x 4” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Apex Cutlass Bearing
A:Shaft Diameter (inches): 1
B:Outside Diameter (inches): 1 and 3/8
C:Length (inches): 4
G:Metal Thickness (inches): 1/16• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$80.64 Add to cart -
Rubber Bearing
Johnson 1-1/4”x 1-1/2”x 5” Cutless Naval Brass Sleeve Bearings
Johnson 1-1/4”x 1-1/2”x 5” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 1/4
B:Outside Diameter (inches): 1 and 1/2
C:Length (inches): 5
G:Metal Thickness (inches): 1/16• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$102.03 Add to cart -
Rubber Bearing
Johnson 1-1/4”x 1-3/4”x 5 Cutless Naval Brass Sleeve Bearings
Johnson 1-1/4”x 1-3/4”x 5 Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 1/4
B:Outside Diameter (inches): 1 and 3/4
C:Length (inches): 5
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$102.86 Add to cart -
Rubber Bearing
Johnson 1-1/4”x 2”x 5” Cutless Naval Brass Sleeve Bearings
Johnson 1-1/4”x 2”x 5” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 1/4
B:Outside Diameter (inches): 2
C:Length (inches): 5
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$108.10 Add to cart -
Rubber Bearing
Johnson 1”x 2”x 4 Cutless Naval Brass Sleeve Bearings
Johnson 1”x 2”x 4 Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1
B:Outside Diameter (inches): 2
C:Length (inches): 4
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$103.89 Add to cart -
Rubber Bearing
Johnson 1-1/4”x 2-1/8”x 5” Cutless Naval Brass Sleeve Bearings
Johnson 1-1/4”x 2-1/8”x 5” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 1/4
B:Outside Diameter (inches): 2 and 1/8
C:Length (inches): 5
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$120.87 Add to cart -
Rubber Bearing
Johnson 1-1/8”X 1-1/2”X 4-1/2” Cutless Naval Brass Sleeve Bearings
Johnson 1-1/8”X 1-1/2”X 4-1/2” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 1/8
B:Outside Diameter (inches): 1 and 1/2
C:Length (inches): 4 and 1/2
G:Metal Thickness (inches): 1/16• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$100.71 Add to cart -
Rubber Bearing
Johnson 1-1/8”X 1-3/4”X 4-1/2” Cutless Naval Brass Sleeve Bearings
Johnson 1-1/8”X 1-3/4”X 4-1/2” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 1/8
B:Outside Diameter (inches): 1 and 3/4
C:Length (inches): 4 and 1/2
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$115.32 Add to cart -
Rubber Bearing
Johnson 1-1/8”x 2” x 4-1/2” Cutless Naval Brass Sleeve Bearings
Johnson 1-1/8”x 2” x 4-1/2” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 1/8
B:Outside Diameter (inches): 2
C:Length (inches): 4 and 1/2
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$154.61 Add to cart -
Rubber Bearing
Johnson 1-3/8”x 2”x 5-1/2” Cutless Naval Brass Sleeve Bearings
Johnson 1-3/8”x 2”x 5-1/2” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 3/8
B:Outside Diameter (inches): 2
C:Length (inches): 5 and 1/2
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$124.42 Add to cart -
Rubber Bearing
Johnson 1-3/8”x 2-3/8”x 5-1/2 Cutless Naval Brass Sleeve Bearings
Johnson 1-3/8”x 2-3/8”x 5-1/2 Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 3/8
B:Outside Diameter (inches): 2 and 3/8
C:Length (inches): 5 and 1/2
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$136.88 Add to cart -
Rubber Bearing
Johnson 1-1/2”x 2” x 6” Cutless Naval Brass Sleeve Bearings
Johnson 1-1/2”x 2” x 6” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 1/2
B:Outside Diameter (inches): 2
C:Length (inches): 6
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$141.84 Add to cart -
Rubber Bearing
Johnson 1-1/2”x 2-3/8” x 6” Cutless Naval Brass Sleeve Bearings
Johnson 1-1/2”x 2-3/8” x 6” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 1/2
B:Outside Diameter (inches): 2 and 3/8
C:Length (inches): 6
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$150.07 Add to cart -
Rubber Bearing
Johnson) 1-3/4”x 2-3/8 ”x 7” Cutless Naval Brass Sleeve Bearings
Johnson 1-3/4”x 2-3/8 ”x 7” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 3/4
B:Outside Diameter (inches): 2 and 3/8
C:Length (inches): 7
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$174.46 Add to cart -
Rubber Bearing
Johnson 1-3/4”x 2-5/8”x 7” Cutless Naval Brass Sleeve Bearings
Johnson 1-3/4”x 2-5/8”x 7” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 1 and 3/4
B:Outside Diameter (inches): 2 and 5/8
C:Length (inches): 7
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$178.70 Add to cart -
Rubber Bearing
Johnson 2”x 2-5/8”x 8 Cutless Naval Brass Sleeve Bearings
Johnson 2”x 2-5/8”x 8 Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 2
B:Outside Diameter (inches): 2 and 5/8
C:Length (inches): 8
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$199.90 Add to cart -
Rubber Bearing
Johnson 2”x 3”x 8 Cutless Naval Brass Sleeve Bearings
Johnson 2”x 3”x 8 Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 2
B:Outside Diameter (inches): 3
C:Length (inches): 8
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$204.02 Add to cart -
Rubber Bearing
Johnson 2-1/4”x 3-1/8” x 9″ Cutless Naval Brass Sleeve Bearings
Johnson 2-1/4”x 3-1/8” x 9″ Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 2 and 1/4
B:Outside Diameter (inches): 3 and 1/8
C:Length (inches): 9
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$258.53 Add to cart -
Rubber Bearing
Johnson 2-1/4” x 2-15/16” x 9″ Cutless Naval Brass Sleeve Bearings
Johnson 2-1/4” x 2-15/16” x 9″ Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 2 and 1/4
B:Outside Diameter (inches): 2 and 15/16
C:Length (inches): 9
G:Metal Thickness (inches): 3/32• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$596.39 Add to cart -
Rubber Bearing
Johnson 2-1/2 x 3-1/8” x 10” Cutless Naval Brass Sleeve Bearings
Johnson 2-1/2 x 3-1/8” x 10” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 2 and 1/2
B:Outside Diameter (inches): 3 and 1/8
C:Length (inches): 10
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$303.25 Add to cart -
Rubber Bearing
Johnson 2-1/2” x 3-3/8” x 10” Cutless Naval Brass Sleeve Bearings
Johnson 2-1/2” x 3-3/8” x 10” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 2 and 1/2
B:Outside Diameter (inches): 3 and 3/8
C:Length (inches): 10
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$304.90 Add to cart -
Rubber Bearing
Johnson 2-3/4” x 3-3/8” x 11” Cutless Naval Brass Sleeve Bearings
Johnson 2-3/4” x 3-3/8” x 11” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 2 and 1/4
B:Outside Diameter (inches): 3 and 1/8
C:Length (inches): 9
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$352.99 Add to cart -
Rubber Bearing
Johnson 2-3/4” x 3-3/4” x 11” Cutless Naval Brass Sleeve Bearings
Johnson 2-3/4” x 3-3/4” x 11” Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 2 and 3/4
B:Outside Diameter (inches): 3 and 3/4
C:Length (inches): 11
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$371.90 Add to cart -
Rubber Bearing
Johnson 3”x 4”x 12″ Cutless Naval Brass Sleeve Bearings
Johnson 3”x 4”x 12″ Cutless ® Naval Brass Sleeve Bearings
Picture Dimensions of Able Cutlass Bearing
A:Shaft Diameter (inches): 3
B:Outside Diameter (inches): 3 and 3/4
C:Length (inches): 12
G:Metal Thickness (inches): 1/8• These bearings adapt equally well to strut and stern tube mounts, and are
often used effectively as rudder-stock and pintle bushings.
• Bearing diameters are precision fitted to the designated shaft size with
the correct clearance for efficient water lubrication.
• External brass shells are machined and polished to provide easy fitting.
• Specially formulated oil and chemical resistant nitrile rubber is securely
bonded to the shell.
• Units with thin shells are available for the struts of small craft.
• Sleeve bearings are usually installed by light press-fitting and locked in
place with cone-pointed set screws.
• PRECAUTION: When shrink fitting of the bearing is required, chilling
must be achieved by gradual cooling to not more than minus 20° F (-28°
C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or
shocking the bearing while in the chilled state could cause the rubber to
separate from the shell.Metallic Rubber Bering
Brand: Duramax Marine LLC
(0 reviews)$375.92 Add to cart
